Warm Audio Reamper

Nýtt

Nánari lýsing

Routing For Any Studio Setup

Reamper gives musicians, engineers, and producers the flexibility to easily connect guitar rigs, studio processors, pedals, and DAWs in ways typically reserved for complex studio setups. Re-amp dry tracks through real tube amps, capture a safety dry signal while recording for tweaking or layering in post, integrate guitar pedals into line-level studio chains or studio processing into guitar or synth signals, and record cranked tube amps silently using a built-in power soak. With the Reamper, that entire process becomes faster, easier, and far more musical.
The Definitive Creative Reamping Tool

Reamper takes the concept of reamping and signal flow much further. With fully independent preamp and re-amp signal paths, CineMag input/output transformers, and variable impedance control, Reamper preserves the tone of your source while adapting to everything from guitars and pedals to synths and line-level studio gear. The built-in 50W/8Ω power soak allows you to capture the full character of cranked tube amps silently, while flexible I/O makes it easy to move between DAW tracks, amps, pedals, and outboard processors without constantly breaking down your workflow. Built to professional studio standards, Reamper brings true analog integration and creative flexibility to any recording setup.
Applications

Re-AmpingReamp Dry Guitar Signals

Silent RecordingRecord Tube Amps Anywhere

Effects ProcessingAny Signal, Any FX Pedal

Daisy-Chain RecordingTwo Amps, One Take

What you need to know

Warm Audio Reamper is a creative routing device with rugged build quality loaded with signal flow tools that are unprecedented on typical “re-amping” devices.

The variable impedance control makes it easy to match input sources to Reamper. With a range of 120kΩ -1MΩ, you can throw anything at Reamper without unwanted noise or distortion.

Separate controls for Preamp Out and Reamp Out allow for separate gain staging when going to studio gear on the Line Out or to the front end of amps when feeding for re-amping. Get the perfect gain for your re-amping and any dry bail-out signals.

Change the character of the direct signal by flipping between a JFET stage for a warmer more vintage vibe, or to Op-Amp when cleaner gain is required.

The “AMP-IN”/“THRU” section enables silent recording of 50W/8Ω tube amps without a cabinet when “THRU” is not connected.** When “THRU” is connected to a speaker cabinet, audio is sent to the cab, with no power or impedance limits when using Reamper this way. When recording silently, make sure to use an Impulse Response (IR) in the DAW for accurate “amp in the room” tone.

** WARNING: Do not connect any bridged amplifiers to Reamper. Do not exceed the 50W/8Ω limitation on Reamper for silent recording. When using the “AMP-IN” feature on Reamper with more powerful amps, connect an appropriate speaker load using the “THRU” connection. Failure to do this may cause damage to your amplifier.

LIFT/GROUND SWITCH: Eliminate noise like hum and buzz caused by ground-loop issues. As more pieces of equipment connect to various power supplies, the chance of ground-loop hum issues increase.

Fender Santa Ana Overdrive V2

Santa Ana V2 is a JFET-based class-A overdrive pedal running at 18V internally — a design that provides the touch sensitivity and high-headroom drive that players expect from a Fender tube amp pushed hard and then some. At its heart, this dual-voice drive circuit sports three straightforward controls and a Voice switch to push your guitar from natural-sounding tight overdrive (voice A) to smooth, thick lead tones (voice B). The Drive and Tone controls provide a wide range to dial in just the right flavor of gain and treble presence in the drive signal, while the rear-mounted Tight switch pulls some pre-drive bass frequencies out for an even more focused feeling drive. To further sculpt the frequency response of your drive, a standalone, independently switchable 3-band EQ circuit is built around the Santa Ana V2 drive engine. Active Bass, Middle, and Treble controls offer a wide range of adjustment, cutting or boosting each frequency range with a center detent to mark flat response. Determine exactly how the EQ circuit interacts by using the EQ Placement switch to stack the EQ before or after the drive: Pre-drive EQ flavors the overdrive’s response by determining which frequencies are clipped most by the drive circuit; post-drive EQ lets your guitar hit the drive head on and shapes the resulting gain tones for a more dramatic EQ effect. With a fine-tuned JFET drive engine, independent EQ circuit, conveniently switchable buffered and true bypass modes, and multiswitch enabled footswitches for momentary and latching activation, the Santa Ana V2 is an ultra-flexible, intuitive overdrive with tons of tones on tap.

Samtals m/vsk

29.990 kr.

Á lager

Fender Pugilist Distortion V2

The Pugilist V2 is a distortion pedal like no other, wielding dual independent distortion engines packed inside one chassis to crank out a wealth of thick tones. Each distortion engine can be turned on separately using its designated footswitch and dialed in using its own Gain, Tone and Level controls. This provides two distinctively flavored distortion voices, with Engine A delivering treble-rich lead drive tones and Engine B laying on thick, heavier distortion. The real magic of Pugilist V2 is in the Path switch, which runs the two distortion engines through three different signal paths as they push each other into harmonically rich saturation. The two Series Modes send one circuit into the other for stacking drive tones that can be layered like amp channels, using the footswitches to kick into the next level of cascading distortion. Parallel Mode delivers deep tone-shaping by running the two engines side by side to be blended and balanced using the level controls to create the perfect meld of articulate, chunky distortion. Featuring global Mid Cut and Bass Boost switches, conveniently switchable buffered and true bypass modes, and multiswitch enabled footswitches for momentary and latching activation, these ever-sparring distortion circuits knock out huge distortion tones with modern conveniences fit for any board.

Samtals m/vsk

29.990 kr.

Á lager

Fender Pelt Fuzz V2

The Pelt V2 is a pro-level fuzz pedal with a classic spirit. Built around silicon transistors and a buffer-friendly input stage, it packs all the fuzzed-out tones a saturation-lover could ask for — from full, biting octave fuzz to smooth, harmonically rich walls of gain. Beyond traditional Fuzz, Tone and Level controls, the Pelt V2 takes saturation shaping to the next level with Sag and Bloom controls to fine tune exactly how your signal breaks and splatters into furry, gain-ladened madness. Use the Mids and Thick switches to deliver extra EQ shaping for mid and bass frequency presence to instantly push into new characters of fuzz. The Octave (Chaos) footswitch takes this fuzz into all-new territory by adding a traditional octave-up effect or, with Chaos engaged, an asymmetrical octave effect for glitchy, sputtering artifacts and unpredictable tonal chaos. To top it off, this buffer and bass friendly pedal features a Blend control that enables mixing of fuzz and clean tones (perfect for bass) or blending fuzz with the drive tone of pedals before it in your signal chain. Featuring conveniently switchable buffered and true bypass modes, multiswitch enabled footswitches for momentary and latching activation, and a world of tone-shaping tools for dialing in the exact fuzz you’re after, the Pelt V2 is the ultimate way to add a gloriously wooly coat to your tone.

Samtals m/vsk

29.990 kr.

Á lager

Fender Bends Compressor V2

An intuitive compressor/boost combo offering low-noise compression in both modern and vintage tube flavors, the Bends V2 is ideal for guitar and bass alike. Utilizing a unique take on OTA technology for real-time gain control, this compressor reacts to your playing dynamics smoothly and naturally to balance the volume of louder and quieter sections while adding sustain and thickness to your notes. The Bends V2 simplifies compression to three clearly labeled controls — a three-speed Attack switch, a fine-tuned Release control, and an Input control which sets the input level of the compression trigger. An active Tone control with a center detent cuts or boost treble to make up for any lost sparkle, and the Blend control injects clean into the mix to provide the perfect balance of clean dynamics and compression. A rear-mounted Vintage switch provides the real secret sauce, reshaping the circuit from a crisp, surgical action to a beautifully colored smooth compression with a hint of natural saturation when engaged. Combine boost and compression for some real magic. The Comp Pre/Post switch rearranges the internal circuit to reorder the independent ultra-clean boost and compression. Place the boost before compression for soaring Nashville-style sustain or stack the boost after your signal is compressed and kick it on for a solo boost to increase the overall output level into your next effects. Featuring an independent boost circuit, switchable buffered and true bypass modes, and multiswitch enabled footswitches for momentary and latching activation, the Bends V2 is a fully featured compressor that brings natural feeling dynamic control to any instrument.

Samtals m/vsk

29.990 kr.

Á lager